TRID : 5227472 Actual Tender Number :

TEC

TEC TEC Setting out pillars , providing & fixing of working benchmark pillars 2 nos. per km & 6 nos. of reference pillars required for 1 km. as per drawings given and direction of e/i", clearing and grubbing road land (by manual means) including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm, removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification clause 201.1 and direction of e/i, "dismantling brick/tile work, dismantling of existing structures, like culverts, bridge, retaining wall and other structures comprising of brick masonary including unserviceable material and stacking the serviceable material with all lift and lead of 1000m as per technical specification clause 202.", "dismantling of structures, dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including t&p and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per technical specification clause 202., a) reinforced cement concrete ", "removing all types of hume pipe and stacking within a lead of 1000m including earthwork and dismantling of masonary works as per technical specification clause 202.1 ., b) above 600 mm to 900 mm dia hume pipe ", "box cutting, excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per technical specification clause 302.3", construction of embankment with approved material deposited from road way cutting and excavation from drain and foundation of other structures and excavated with an average lead of 50 m graded and compacted to meet requirement of tables 300.1 and 300.2 as per technical specification clause 301.5 (including royality & labour cess)., "construction of embankment with material obtained from borrow pits with a lift upto 1.5 m , transporting to the site spreading , grading to required slope and compacting to meet requirement of tables 300.1 and 300.2 with a lead upto 1000 m & 100 m as per technical specification clause 301.5 . (including royality & labour cess)., for 1000 m lead @ 20 %", for 100 m lead @ 80%, "construction of subgrade and earthen shoulders, construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000 m & 100 m as per technical specification clause 303.1. (including royality & labour cess).", "granular sub-base with well graded material (table 400.1), ( by mix in place method ) for grading i materialconstruction of granular sub-base by providing well graded material, spreading in uniform layers with tractor mounted grader arrangement on prepared surface, mixing by mix in place method with rotavator at omc, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification clause 401.", "wbm grading 3 (by mechanical means), providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kn in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per technical specification clause 405.", "cement concrete pavement, construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 m30 (grade), coarse and fine aggregates conforming to is:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, using curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification clause 1501", "hard shouldering, laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kn as per technical specification clause 412", "cable duct across the road providing and laying of a reinforced cement concrete pipe duct, 300 mm dia, across the road (new construction), extending from drain to drain in cuts and toe of slope to toe of slope in fills, constructing head walls at both ends, providing a minimum fill ofgranular material over top and sides of rcc pipe as per irc:981997, bedded on a 0.3 m thick layer of granular material free of rock pieces, outer to outer distance of pipe at least half dia of pipe subject to minimum 450 mm in case of double and triple row ducts, joints to be made leak proof, invert level of duct to be above higher than ground level to prevent entry of water and dirt, all as per irc: 98 - 1997 and approved drawings., ", "kilometre stone , reinforced cement concrete m15 grade kilometre local stone of standard design asper irc:8 fixing in position including painting and printing , etc as per drawing and technical specification clause 1703., ii) km stone ", iii) 200 m stone , "retro-reflectorised traffic signs, providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per irc:67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with m15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and technical specification clause 801, 600 mm equilateral & triangle, (left hand, right hand curve & school board) 600 mm equilateral & triangle, ", 900 mm side octagon, or , 600 mm x 450 mm rectangular, , "road marking with hot applied thermoplastic compound with reflectorising glass beads on concrete surface, providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per irc:35 .the finished surface to be level, uniform and free from streaks and holes. sealing primer may be applied in advance which is incidentally included to the work.", "(i)providing and fixing 'logo' of mmgsy project , providing and fixing of typical mmgsy informatory sign board with logo as per mord specifications and drawing. three ms plates of 1.6 mm thick, top and middle plate duly welded with ms flat iron 25mm x 5m size on back on edges. the lower plate will be welded with ms angle iron frame of 25mm x 25mm x 5mm. the angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 swg sheet tubes posts duly em at

Key Values